RE: [cobalt-users] dmesg errors

[Mark Spieth <mspieth@xxxxxxxxxxxx>]

Unable to load interpreter is generally what you see when you run out of ram
and the system cannot load in part of the Linux kernel. This is generally
followed up by a system crash.

MASQ failing checksum can be many things, if you only see it once, don't
worry about it.

-----Original Message-----
From: Jonathan D. Hozeska [mailto:jhozeska@xxxxxxxxxxx]
Sent: Friday, February 18, 2000 11:54 AM
To: cobalt-users@xxxxxxxxxxxxxxx
Subject: [cobalt-users] dmesg errors


Recently I read an article which stated "'dmesg,' the Unix command that
tells you the startup and other system diagnostics."  So I tried it and got
the following.  Everything looks fine (as far as I know) except for a few
lines at the very bottom. I have a series of "Unable to load interpreter"
and "MASQ: failed TCP/UDP checksum from 194.222.185.112!".
 
Should I be concerned?  Can someone please explain?

Thank you.
 
--------
 [admin admin]$ dmesg
 Loading R4000 MMU routines.
 CPU revision is: 000028a0
 Primary ICACHE 32K (linesize 32 bytes)
 Primary DCACHE 32K (linesize 32 bytes)
 ns16550: console I/O
 Probing PCI hardware.
 Calibrating delay loop.. ok - 249.86 BogoMIPS
 Memory: 127744k/131068k available (1196k kernel code, 2128k data)
 Swansea University Computer Society NET3.035 for Linux 2.0
 NET3: Unix domain sockets 0.13 for Linux NET3.035.
 Swansea University Computer Society TCP/IP for NET3.034
 IP Protocols: IGMP, ICMP, UDP, TCP
 Linux IP multicast router 0.07.
 Appletalk 0.17 for Linux NET3.035
 VFS: Diskquotas version dquot_5.6.0 initialized
 Checking for 'wait' instruction...  available.
 Linux version 2.0.34 (root@xxxxxxxxxxxxxxxxxxxx) (gcc version 2.7.2) #1 Wed
 May
 5 16:04:43 PDT 1999
 Starting kswapd v 1.5
 Serial driver version 4.13 with no serial options enabled
 tty00 at 0x1c800000 (irq = 7) is a 16550A
 Real Time Clock Driver v1.09
 Cobalt LCD Driver v2.10
 loop: registered device at major 7
 ide: Cobalt Networks IDE controller.
 GAL CFG[00000001-->00000003]
     ide0: BM-DMA at 0x1000cc00-0x1000cc07
     ide1: BM-DMA at 0x1000cc08-0x1000cc0f
 hda: QUANTUM FIREBALL CR8.4A, 8063MB w/418kB Cache, CHS=16383/16/63, UDMA
 ide0 at 0x100001f0-0x100001f7,0x100003f6 on irq 14
 md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
 linear personality registered
 raid0 personality registered
 raid1 personality registered
 raid5 personality registered
 scsi : 0 hosts.
 scsi : detected total.
 PPP: version 2.3.5 (demand dialling)
 TCP compression code copyright 1989 Regents of the University of California
 PPP line discipline registered.
 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256).
 CSLIP: code copyright 1989 Regents of the University of California.
 SLIP linefill/keepalive option.
 tulip.c:v0.76 4/22/97 becker@xxxxxxxxxxxxxxxxxxxx
 eth0: DEC 21142 Tulip at 0x10100000, 00 10 e0 00 27 4c, IRQ 4
 
 eth0: Old format EEPROM on 'Cobalt 27' board.  Using substitute media
 control in
 fo.
 eth0: EEPROM default media type MII 10baseT.
 eth0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
 Partition check:
  hda: hda1 hda2 hda3 hda4
 VFS: Mounted root (ext2 filesystem) readonly.
 Adding Swap: 130748k swap-space (priority -1)
 sysctl: ip forwarding off
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 Unable to load interpreter
 MASQ: failed TCP/UDP checksum from 194.222.185.112!
 [admin admin]$

_______________________________________________
cobalt-users mailing list
cobalt-users@xxxxxxxxxxxxxxx
http://list.cobalt.com/mailman/listinfo/cobalt-users