RE: [cobalt-developers] Onstream Tape Drives & Cobalt Qube 3?

["Kevin Thomson" <webservices@xxxxxxxxxxxxxx>]

Just tried the following (exactly, and get these responces:

[root /]# mount /dev/st0
mount: can't find /dev/st0 in /etc/fstab or /etc/mtab
[root /]#

[root /]# mount -f /dev/st0
mount: can't find /dev/st0 in /etc/fstab or /etc/mtab
[root /]#

[root /]# mount /dev/st0 status
mount: /dev/st0 is not a block device
[root /]#

and lastly:
[root /]# mount -f /dev/st0 status
[root /]#

Which if I type mount afterwards to see the mounting points shows me:
[root /]# mount
/dev/md1 on / type ext2 (rw)
none on /proc type proc (rw)
/dev/md3 on /var type ext2 (rw,nosuid)
/dev/md4 on /home type ext2 (rw,usrquota,grpquota,grpid)
none on /dev/pts type devpts (rw,gid=5,mode=0620)
/dev/st0 on status type unknown (rw)
[root /]#

So is this all there is to it? or am I missing something entirely? like
where I'm mounting this to (ie dir)?

Thanks
-Kevin

-----Original Message-----
From: robert [mailto:rob@xxxxxxxxxxxxxxx]
Sent: Friday, February 16, 2001 4:57 AM
To: Kevin Thomson
Cc: cobalt-developers@xxxxxxxxxxxxxxx
Subject: Re: [cobalt-developers] Onstream Tape Drives & Cobalt Qube 3?



use 'mount' instead of 'mt'



On Fri, 16 Feb 2001, Kevin Thomson wrote:

> Alright, I'm definatly up against a brick wall here and I'd really really
> appreciate some assistance if anyone knows how to install a scsi tape
drive
> (specificaly the Onstream ADR50 External) onto a Qube 3 using the built in
> scsi adapter.  Initialy we plugged it in, rebooted the box and essentialy
> funbled around looking for commands to mount the drive, then Onstream did
> Officialy anounce their compatability with Linux and put out this info as
> they're "installation guide":
>
> 	Installation
>
> 	The LINUX operating systems have a built in device driver called st. The
> LINUX installation program will probe your system for SCSI >>	adapters. In
> some cases, the installation program will ask the user if they have
attached
> any SCSI adapters. If you choose YES, a 	dialog box will appear to select
> from a list of SCSI drivers. Choose the driver that most closely resembles
> the SCSI adapter. The 	installation program may then give you the
> opportunity to specify options for the SCSI driver you selected. Most SCSI
> drivers detect 	your hardware automatically.
>
> 	Install as follows:
>
> 	1. Shutdown the system and remove power from the system. Connect the tape
> peripheral to the SCSI bus, adhering to the rules of SCSI for 	bus
> termination, cable length, and ID selection (See Users Manual for detailed
> description)
>
> 	2.Power on the system, peripherals first.
>
> 	3. Boot the system to the system maintenance mode and login as root.
>
> 	4. At the command prompt, type : mt -f /dev/st0 status. This should
display
> information about the tape drive. If this does not occur, 	re-check your
> set-up.
>
> At first I thought "great now I can continue working on the backup
software"
> till I actualy tried "mt -f /dev/st0 status" through telnet and get a
> "command not found" responce for "mt".  So I'm thinking, okay, maybe they
> meant Mount, or mnt, no go there either as far as getting the device to
> work.  Anyways, I call Onstream, The tech support people swear up and down
> that the mt command stands for magnetic tape drive and its part of the st
> driver, stating that if that command isn't found that its a fault of the
> distrobution and I need to get an updated source of the kernel and
> recompile.
>
> So, any ideas/insight into this? I did a little poking around and the "st
> driver" is present in the kernel source on the Qube 3 but I'm not sure
> whetehr it is modularized in the compiled kernel or even if its installed
in
> the current configuration.  If it is a matter of recompiling the kernel
> could someone point out a good tutorial for this proccess that works on
the
> cobalt procduct(s)?
>
> Thanks
> Kevin Thomson
> webservices@xxxxxxxxxxxxxx
>
>
>
> _______________________________________________
> cobalt-developers mailing list
> cobalt-developers@xxxxxxxxxxxxxxx
> http://list.cobalt.com/mailman/listinfo/cobalt-developers
>

--

Robert Abraham, CEO
HyperAccess Communications, Co.
50 N. Walkup Ave
Top Floor
Crystal Lake, IL 60014
815.356.3983 - Office
815.621.5282 - Cell