[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[cobalt-developers] 'We serve it, you surf it sometimes'

Hello, we are trying to interpret these results from the "Console On"
feature output via the serial cable from a new drive that keeps rebooting
during the Checking Disk stage. When unmounted in a second box, we run
fsck /dev/hdb4 for the /home directory, we receive these errors:

Nov 15 17:55:50 ns2 kernel: hdb: read_intr: status=0x59 { DriveReady
SeekComplet
e DataRequest Error }
Nov 15 17:55:50 ns2 kernel: hdb: read_intr: error=0x40 { UncorrectableError
}, L
BAsect=1288393, sector=169
Nov 15 17:55:50 ns2 kernel: end_request: I/O error, dev 03:44, sector
169
Nov 15 17:55:53 ns2 kernel: hdb: read_intr: status=0x59 { DriveReady
SeekComplet
e DataRequest Error }
Nov 15 17:55:53 ns2 kernel: hdb: read_intr: error=0x10 { SectorIdNotFound
}, LBA
sect=1288394, sector=170
Nov 15 17:55:57 ns2 kernel: hdb: read_intr: status=0x59 { DriveReady
SeekComplet
e DataRequest Error }
Nov 15 17:55:57 ns2 kernel: hdb: read_intr: error=0x10 { SectorIdNotFound
}, LBA
sect=1288394, sector=170
Nov 15 17:56:01 ns2 kernel: hdb: read_intr: status=0x59 { DriveReady
SeekComplet
e DataRequest Error }
Nov 15 17:56:01 ns2 kernel: hdb: read_intr: error=0x10 { SectorIdNotFound
}, LBA
sect=1288394, sector=170
Nov 15 17:56:04 ns2 kernel: hdb: read_intr: status=0x59 { DriveReady
SeekComplet
e DataRequest Error }
Nov 15 17:56:04 ns2 kernel: hdb: read_intr: error=0x10 { SectorIdNotFound
}, LBA
sect=1288394, sector=170
Nov 15 17:56:04 ns2 kernel: ide0: reset: success

These errors are repeated 4 times and then re-boots through the same
cycle repeatedly. Is there any way to salvage the data on hda4 since
we can mount the other partitions hda1 & hda3 via a second box?  The
null cable output results are below to help with possible diagnosis:

ìCobalt Microserver Diagnostics - 'We serve it, you surf it'

Built Fri Jun  11 14:07:25 PST 1999

 1.LCD Test................................PASS
 2.Controller Test.........................PASS
 5.Bank 0:.................................64M
 6.Bank 1:................................. 64M
 7.Bank 2:................................. 64M
 8.Bank 3:................................. 64M
 9.Serial Test.............................PASS
10.PCI Expansion Slot....................**EMPTY**
12.IDE Test................................PASS
13.Ethernet Test...........................PASS
16.RTC Test................................PASS
BOOTLOADER: trying to boot from partition /dev/hda1
Decompressing -\|/-\|/-\|/-\| done
Decompressing -/-\|/-\|/-\|/-\|/-\ done.
Loading R4000 MMU routines.
CPU revision is: 000028a0
Primary ICACHE 32K (linesize 32 bytes)
Primary DCACHE 32K (linesize 32 bytes)
ns16550: console I/O
Probing PCI hardware.
Calibrating delay loop.. ok - 249.86 BogoMIPS
Memory: 257212k/262140k available (1076k kernel code, 3852k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
Linux IP multicast router 0.07.
VFS: Diskquotas version dquot_5.6.0 initializedChecking for 'wait' instruction...
 available.
Linux version 2.0.34C53_SK (root@xxxxxxxxxxxxxxxxxxxx) (gcc version 2.7.2)
#1 Tue May 9 14:57:21 PDT 2000
Starting kswapd v 1.5 
Serial driver version 4.13 with no serial options enabled
tty00 at 0x1c800000 (irq = 7) is a 16550A
Real Time Clock Driver v1.09
Cobalt LCD Driver v2.10
ide: Cobalt Networks IDE controller.
GAL CFG[00000001-->00000003]
    ide0: BM-DMA at 0x1000cc00-0x1000cc07
    ide1: BM-DMA at 0x1000cc08-0x1000cc0f
hda: ST330630A, 29188MB w/2048kB Cache, CHS=59303/16/63, UDMA
ide0 at 0x100001f0-0x100001f7,0x100003f6 on irq 14
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
linear personality registered
raid0 personality registered
raid1 personality registered
raid5 personality registered
scsi : 0 hosts.
scsi : detected total.
eth0: Digital DS21143 Tulip rev 65 at 0x10100000, 00:xx:xx:00:xx:xx,
IRQ 4.
eth0: Old format EEPROM on 'Cobalt 27' board.  Using substitute media
control info.
eth0:  EEPROM default media type Autosense.
eth0:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
eth0:  MII transceiver #1 config 1000 status 7809 advertising 01e1.
eth1: Digital DS21143 Tulip rev 65 at 0x10101000, 00:10:E0:00:43:E0,
IRQ 13.
eth1: Old format EEPROM on 'Cobalt 27' board.  Using substitute media
control info.
eth1:  EEPROM default media type Autosense.
eth1:  Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
eth1:  MII transceiver #1 config 1000 status 7809 advertising 01e1.
Partition check:
 hda: hda1 hda2 hda3 hda4
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 130748k swap-space (priority -1)
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=1288394, sector=164
end_request: I/O error, dev 03:04, sector 164
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=1288394, sector=166
end_request: I/O error, dev 03:04, sector 166
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x40 { UncorrectableError }, LBAsect=1288394, sector=168
end_request: I/O error, dev 03:04, sector 168
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288395, sector=170
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288395, sector=170
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288395, sector=170
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288395, sector=170
hda: disabled DMA
ide0: reset: success
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error
}
hda: read_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288394, sector=170
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error
}
hda: read_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288394, sector=170
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error
}
hda: read_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288394, sector=170
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error
}
hda: read_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288394, sector=170
ide0: reset: success
hda: read_intr: status=0x59 { DriveReady SeekComplete DataRequest Error
}
hda: read_intr: error=0x10 { SectorIdNotFound }, LBAsect=1288394, sector=170
end_request: I/O error, dev 03:04, sector 170 

Thanks in Advance,
-- 
James Hoaggs   ICQ #96365505
james_hoaggs@xxxxxxxxxx - email
(408) 380-2271 x8024 - voicemail/fax



__________________________________________________
FREE voicemail, email, and fax...all in one place.
Sign Up Now! http://www.onebox.com